If you are just using two servers that are load balanced using NLB then you need to allow only the listening ports of the web servers. Suppose you have one site that accepts only secured requests port The NLB service will only redirect an incoming request between the web servers that are part of the load balancer thus you just need to open the rules from the NLB server to each Web Server on port both ways. Hope this will server you well.
We have a windows console application and it is running as a windows scheduler, can we depend on NLB concept and just keep another instance of the app running on different server. My question is that, Which type of applications can configure on NLB. Means which type of applications supported on NLB?? Download Trial. Buy Now. For testing purposes I will add a random IP address: The next section is used to configure cluster parameters.
A NLB cluster must operate in one of the following modes: Unicast — the MAC address of the cluster virtual network adapter is shared with all cluster nodes. From the three available options, choose multicast and proceed with the next section: From the port rules section we configure how traffic is managed on the NLB cluster.
There are three available filtering methods, as follows: Multiple host — used to configure all nodes within the NLB cluster to respond to requests. We will add the second server by right clicking the cluster and selecting Add Host to Cluster: Now you will need to follow the same procedure as we did earlier for the first node.
Dan Popescu. February 3, at am. Popescu Dan says:. February 5, at am. Vineetha says:. February 17, at am. Ehsan says:. To support scalability, you can do the following with NLB:. Balance multiple server load requests from the same client or from several clients across multiple hosts in the cluster. Enable high performance and low overhead through a fully pipelined implementation.
Pipelining allows requests to be sent to the NLB cluster without waiting for a response to a previous request. Specify the load balancing behavior for a single IP port or group of ports by using port management rules. Define different port rules for each website.
If you use the same set of load-balanced servers for multiple applications or websites, port rules are based on the destination virtual IP address using virtual clusters. Direct all client requests to a single host by using optional, single-host rules. NLB routes client requests to a particular host that is running specific applications. Enable Internet Group Management Protocol IGMP support on the cluster hosts to control switch port flooding where incoming network packets are sent to all ports on the switch when operating in multicast mode.
NLB logs all actions and cluster changes in the event log. NLB is installed as a standard Windows Server networking driver component. The following figure shows the relationship between NLB and other software components in a typical configuration. Provides Network Load Balancing Tools to configure and manage multiple clusters and all of the hosts from a single remote or local computer. Enables clients to access the cluster by using a single, logical Internet name and virtual IP address, which is known as the cluster IP address it retains individual names for each computer.
NLB allows multiple virtual IP addresses for multihomed servers. Enables NLB to be bound to multiple network adapters, which enables you to configure multiple independent clusters on each host. Support for multiple network adapters differs from virtual clusters in that virtual clusters allow you to configure multiple clusters on a single network adapter.
Can be configured to automatically add a host to the cluster if that cluster host fails and is subsequently brought back online. In this example, you add network interfaces to the back-end pool. You must repeat this step for each network interface that can process requests made to the VIP. You can also repeat this process on a single network interface to add it to multiple load balancer objects.
For example, if you have a load balancer object for a web server VIP and a separate load balancer object to provide outbound NAT. Get the network interface and add the backendaddress pool to the loadbalancerbackendaddresspools array. If you need to map a Virtual IP to a single network interface on a virtual network without defining individual ports, you can create an L3 forwarding rule.
This process does not require you to create a load balancer object. Assigning the PublicIPAddress to the network interface is enough information for the Software Load Balancer to perform its configuration. This example repeats the same action as the previous example, but it automatically allocates the VIP from the available pool of VIPs in the load balancer instead of specifying a specific IP Address.
This example removes the PublicIPAddress resource that was created by the previous examples. Skip to main content. This browser is no longer supported.
0コメント