Furniture woodworking tools

There's a distinct difference between using your own strength and skills to shape your woodworking projects—feeling the surface of the wood, its texture, and shaping it, letting your creativity loose—as opposed to using power tools, which in their own right require a level of skill and experience to use properly. Prior to the introduction of motorized power tools, hand tools bridged the gap between rough lumber and finished projects.

Woodcraft features the largest selection of woodworking hand tools you need for your projects. From axes to wrenches, chisels to planes, and everything in between, you will find it at Woodcraft! Quick View. Add to Cart. Pica - Dry Longlife Automatic Pencil. Razorsaw - Ryoba Saw mm No. WoodRiver - Wheel Marking Gauge. Wixey - 8" Digital Protractor and Rule.

Groz - Caliper and Divider Set - 3 Piece. Pica - -Dry Refills Set White. Milescraft - SquareClampKit. Wixey - Mini Digital Height Gauge. Crown - Mini Beech Marking Gauge. Westcott - 6" See-Through Acrylic Ruler. Find a Store. My Account. My Cart. Go to Home Page.

Hammers with a steel handle, or even fiberglass, will be stronger. The next important hand tool for the woodworker is an accurate tape measure.

Get a retractable one that is at least 25 feet long. Any longer than that, and you start having problems getting it to roll back up. This can add up to some severe accuracy problems in the long run. A good utility knife is another asset for the woodworker. There are many different kinds, but the kind that uses disposable blades is the most common.

The blade retracts into the grip for safety. The woodworker will use the utility knife when cleaning out mortise joints or to scribe wood, as well as many other uses. A quality wood moisture meter is vital to the long-term success of any woodworking project you put together.

Lumber mills try to dry their batches of lumber according to the intended end product destination. That is, if the wood is harvested in the wet Northeast, but is going to be shipped to the arid Southwest, it will be dried more than wood kept in the Northeast for use by woodworkers.

The success of your woodworking project, from wood flooring to kitchen cabinets to fine furniture, depends on the correct moisture content levels of the woods you use for your area of the country. Some moisture meters have pins that penetrate the surface of the wood.

This can leave tiny holes that mar the surface and require filling. Others are pin-less. They have sensing plates that scan the wood beneath. Your wood moisture meter should have settings on it that will account for different species of wood. For instance, oak is a hardwood, but ebony is an even harder-density wood. If you are planning an inlay job using both types of wood, you will need to know the moisture content levels of each of the two species so that your inlay glue joints will stay intact.

These different wood species have different specific gravities, which must be used or programmed into the moisture meter.

Learn more about Pinless meters in our moisture meter guide. Buy an Orion Meter. Therefore, you must measure each species of wood you are using in your woodworking project to verify that they are at the correct moisture content before you manufacture it into your end product.

An assortment of chisels should be part of every workbench. Chisels are not just for woodcarvers. Any woodworker will need chisels to clean out joints and saw cuts. Look for chisels made of high-alloy carbon steel or chromium-vanadium alloyed steel. Hardwood grips are best, especially if they have metal caps on them. This will keep the end of the handle from becoming malformed when you hammer on it. The smallest chisels are best for mortise work.

You can even get a corner chisel that cuts a notch out of the wood with the blow of a hammer, much like a hole punch. Most chisels are beveled on the 2 sides and on the cutting edge, but specialty chisels may only be beveled at the cutting edge. This bevel will be at 20 to 25 degrees down the length of the blade on one side, and flat on the backside. Make sure you get chisels with a grip that fits your hand. This will prevent them from bouncing around in your toolbox drawers and getting damaged.

Using your chisels involves both hands. This allows for power and control of the chisel as it pares away the wood. A claw hammer will damage the butt end of your chisel, eventually splitting it if you abuse it too often.

When you sharpen your chisel, you may want to use stones rather than a grinder. You need a set of stones of increasingly fine grit to hone the blades properly. Start with the coarser grade, and end with the finest grade.

You may have to moisten the stone with oil for best results. Also, remember to hone the blades away from your body. Every woodworker needs a couple of levels. Level means horizontal, and plumb is vertical. Most quality levels are made of either brass-edged wood or of metal. There will be a bubble reading for level, and another one for plumb.

When the bubble is exactly between the lines, you have a level or plumb surface. You can also get string levels and laser levels, but the woodworker will use these types of levels the most often. Quality construction is vital to a good set of screwdrivers.

This gives you a lot of torque. This is accomplished with a cabinet screwdriver. Get a couple of medium Phillips head screwdrivers, and a stubby one too, for those tight places. You may also want a ratcheting screwdriver. The next hand tool every woodworker should have is a nail set. In fact, you should have several sizes. They look like awls, and you use them to drive nail heads into the wood so they are flush or right below the surface.

This allows you to fill the holes and prepare for staining or painting. The nail setter will usually have either a convex or concave surface to grip the nail better and keep it from sliding off and marring the wood. This is adjustable, and you can lock it at the angle you want to mark, making it much more time-savvy to mark multiple angles. Shop Wood Moisture Meters. The layout square is a triangle that you can use to mark square cuts on stock.

Once you measure the length of the cut, you line up the layout square with the edge of the board. The short side will give you a straight, square cut across the end grain.

You can also measure off angles with the layout square. You can even use your layout square to determine an existing angle. Just be sure to buy one made of metal. The plastic ones are not only fragile, but they also can warp, making them pretty useless. As Sales Manager for Wagner Meters, Ron has more than 35 years of experience with instrumentation and measurement systems in different industries. In previous positions, he has served as Regional Sales Manager, Product and Projects Manager, and Sales Manager for manufacturers involved in measurement instrumentation.

Last updated on September 14th, Nice info, I am very thankful to you that you have shared this special information with us. I got some different kind of knowledge from your web page, and it is really helpful for everyone.

Thanks for share it. Read more info about curved edge console table online. Hello, This is a good article and the content is very useful. Wish to read more articles in the future. Keep posting, Thank You. It was helpful for my project on smart woodworking tools. Thanks a lot. As a woodworking expert, I tell you what, You just mentioned the right tool that needs the most.

Thanks for helping people. Thanks for sharing this beautiful post about woodworking tools. Thanks for this beautifully written post with great knowledge. I learned a few things that will hopefully help me going forward. Thanks for sharing the article.

It is very Informative. Really helpful for a woodworker, It helped me a lot in developing my smart woodworking tools website. Good article! We will be linking to this great post on our site. Keep up the great writing.

Thanks for this in-depth review. Fortunately, I come across to your website and it helps to make my decision. Thank you again for this great article.

Thanks for your great resource. Such a helpful post you share helps me more and choose the perfect tools for my home mini task complete. By following your website a great safety ensure to using these tools. Just like a benchtop mortiser, a chain mortiser allows you to easily cut mortises in your wood stocks.

With the chain mortiser however, you get to cut mortises in really thick stocks of wood, like beams for timber framing and logs for long home building. Then you need a moisture meter. It can shrink, twist or even split.

If you love turning wood into different shapes and objects, then you should be already familiar with the wood lathe.

You can turn any block of wood into decorative pieces if you know your way around the tool. Biscuit joints are one of my favorite woodworking joints, and creating them can only be done when you have a biscuit joiner in hand. Woodworking clamps are a necessity in any woodshop.

You need them for clamping pieces together for gluing, drilling and several other activities. Eyeballing it is not really advisable in many cases if you need maximum precision and want to do a quality job. The woodworking tool you need in this case is a center scriber.

In order to carry out your woodworking projects, you need to measure each piece correctly, which makes a good measuring tape essential in your workshop.

The multi-mark tools is a very useful and multi-purpose tool you can use during your woodworking projects. It can be used for squaring, leveling and even transferring measurement. You can find and measure angles accurately using this digital protractor. With it you can adjust angles of your table saw blade, bandsaw and miter saw blades to make accurate bevel cuts. You can measure multiple angles, mark and transfer templates with the multi-angle measuring ruler. A power handsaw is just your normal handsaw powered by an electric motor.

You can cut wood and other material, even metal with it. Kindly let me know if you have any in stock and the price and I would let you know the quantity I may order. Hope to hear from you soon. Hello Martin. If you want to raise the shelf, move the pins up a hole or two. BUT, first, you have to drill the holes. The Kreg Shelf Pin Jig allows you to drill equally spaced holes for this without any set up or measuring.

You literally just hold or clamp the jig, and drill into the slots. I like to set mine flat on the cabinet bottom, drill into the top hole, then I use the included pin inserted into the bottom hole of the jig and into the hole I just drilled in the cabinet to hold my place while I work my way up the cabinet. Run these holes up both sides of the back and both sides of the front. These are the diameters of the pin holes. So be sure to order the correct pin size to fit your jig. You can use my drawer building guide post to help you determine where your slide should go.

Then, clamp these guides onto the cabinet at that location and install the slide. I may not use these often to install my slides, but I do really love them for helping me install my drawers. Once the slides are in place, I can turn these around and clamp the opposite direction to hold my drawers still while I install them onto the slides. And finally, if you are installing new hardware on cabinets, furniture, etc, this is a handy jig to use to keep things consistent. To set it up, simply measure the distance of the screw holes on your pulls measure center to center and adjust the drilling holes on the front of the jig to match.

Note that one side is metric and one side is standard. Then, you just have to measure to find the center of the drawer horizontally, clamp in place, and drill the holes for the pull. It works the same for the doors, too. Simply adjust the distance you want the pulls to be from the door edge, clamp in place and drill.